MMC castings, MMC Hammer, MMC blow bar, MMC Jaw plate,MMC cone, High Mn Steel ceramic composite, High Cr ceramic composite, Martensite steel ceramic composite
Location: Home > Product > Ceramic insert castings > MMC Jaw plate - Ceramic insert Jaw plate
-
-
MMC Jaw plate - Ceramic insert Jaw plate
We have mature and advanced MMC casting technology and We can produce all kinds of wear-resisting parts of crusher by MMC casting technology. The spare parts by ceramic compound casting is high wear resistant, the life span is several times of the traditional material. Our product include: MMC-Mn - High Mn Steel matrix ceramic composite Jaw plate, Hammer, Mantle/Cone, Blow bar, Liner for Ballmill, Liner of AG/SAG. MMC-Cr - High Cr cast iron matrix Ceramic composite blow bar, Liner, Hammer, Downspout, Grinding roller and liner of vertical mill, Impeller, Liner and hammer of VSI. MMC-M - Martensite Steel matrix Ceramic composite Liner, Blow bar, Hammer, Liner of Downspout, weldability wear-resistant plate. If you are interested in MCC Wear Resistant Spare Part, please do not hesitate to contact us immediately. I will supply best competitive price! and product of high quality!
Detail:
DJM 陶瓷復合鄂式碎機備件（齒板）技術介紹
DJM ceramic composite jaw crusher spare parts (jaw plate) technology introduction
顎式破碎機的工作部分是兩塊顎板，一是固定顎板（定顎），垂直（或上端略外傾）固定在機體前壁上，另一是活動顎板（動顎），位置傾斜，與固定顎板形成上大下小的破碎腔（工作腔）?；顒宇€板對著固定顎板做周期性的往復運動，時而分開，時而靠近。分開時，物料進入破碎腔，成品從下部卸出；靠近時，使裝在兩塊顎板之間的物料受到擠壓，彎折和劈裂作用而破碎。顎式破碎機目前廣泛使用的齒板多是采用高錳鋼制造。由于物料的沖刷，破碎過程中的擠壓，碾磨作用，造成齒板磨損嚴重，針對這一情況，DJM 選用高錳鋼為基材的陶瓷復合材料，即齒板的基體采用高錳鋼，同時在基體上嵌鑄具有高耐磨性的陶瓷隨形加強筋，在保持高錳鋼原有的加工硬化耐沖擊性能的同時提高了高錳鋼的耐磨強度，陶瓷復合材料齒板的壽命約為高錳鋼齒板的2倍以上。
Work part of the jaw crusher is two pieces of jaw plate, one is the fixed jaw plate (fixedjaw), which is vertical (or the upper slightly extraversion) fixed in front of the body wall, the other is movable jaw plate (movable jaw),which is tilt, form big end dowm crushing cavity (work cavity). movable jaw plate press the fixed jaw plate with periodic reciprocating motion, sometimes separately, sometimes near. Separately, material into the crushing cavity, finished products dischargefrom the lower ; Approached, the materials are squeezed between two pieces of jaw plate, bending and fracturing effect to broken. Jaw crusher is widely used high manganese steel manufacturing . Due to the material erosion, theextrusionprocess broken, grinding effect, cause plate wear serious, in order to solve this situation, DJM chooses high manganese steel as base material of the ceramic composite materials, which is plate basement with high manganese steel and then embed the high wear resistance With stiffener into the basement.below keeping original work hardening of high manganese steel impact resistance performance and improving wear resistance strength at the same time, the life of the ceramic composite plate is about 2 times longer than the high manganese steel basement plate.
Product include: Mn18Cr2+Ti-Re Mn18Cr2 Mn13 Mn13Cr2 Martensite steel
附圖-2高錳鋼陶瓷復合齒板外觀示意圖
Picture-2 High Mn ceramic composite jaw plate external view
Pre Item:None
Next Item:None
Next Item:None
Product
Contact:
Tel: +86-10-8890 9291/8890 9293
Fax: +86-10-8890 9288
Email: info@djm-bj.com
Web: www.www22599.com
- BEIJING JINMEI ENTREPRENEUR CO .,LTD
- Tel: 86-10-8890 9291/8890 9293 Fax: 86-10-8890 9288 Email: info@djm-bj.com
- Room No.1403 TaiRan Building, No.36 GuSheng Road, ShiJingShan District, Beijing, China.100043
- Copyright 2006-2018 DJM All Right Reservered. Report To Improve Product
京ICP備11022145號-2 - MMC Mill part, MMC Impact bar, MMC Mantle, MMC Crusher part, Ceramic composite High Mn Steel, ceramic particules composite casting,ceramic Insert composite castings
Powered by
MetInfo
3.0 ©2008-2022
www.MetInfo.cn